V5700F - Wiremold

For Installing Raceway Around Offsets, Side Bends, Twisted Turns, and Curved Surfaces. Wire Fill Capacity Is The Same As 500 and 700 Series Raceways. Consult Factory For Custom Lengths. Maximum Painted Length 3' (915MM).

V512 - Wiremold

This Ivory Fittinig Allows 500 Raceway to Make A 45 Degree Turn On Same Surface or Wall. Finish - Ivory

V2010A3 - Wiremold

1/2" Trade Size Kos Located On End, Sides, and Bottom Of Fitting. 3/4" Kos On Bottom and Rear. Includes Ground Screw. Ivory

1585 - Wiremold

For Connecting 1/2" Trade Size Conduit or Armored Cable to 1500 Series Raceway.

2310B - Wiremold

For Closing Open End Of 2300BAC and 2300BACD Series Raceway. Ivory

23482 - Wiremold

Two-Gang. For Deeper Switches and Devices. Base Has Rectangular Ko to Enable Extension From Existing Flush Wall Box and 1/2" and 1" Trade Size Concentric Kos. Accepts Industry Standard Faceplates For Switch and Communication Devices. Ivory

2417MFW - Wiremold

Inside 90 Degree Angle Turns. Fog White

25DTC412 - Wiremold

Two-Compartment Pole. Nominal Material Thickness .040" (1.0MM). Ivory Boot Base. Furnished Unwired Without Outlets. Mounting Hardware, Entrance End Plate and Ceiling Trim Plates Furnished. Length: 12' 5" (3.8M).

25DTC412WH - Wiremold

Tele Power Pole Blank Steel White 12FT.Dimensions: 141.00 X 2.30 X 2.25

25DTC4WH - Wiremold

Tele Power Pole Blank Steel White 10FT.Dimensions: 117.00 X 2.30 X 2.25

25DTPE10WH - Wiremold

WM 25DTP-E10WH Tele-Power Express P

2600WC - Wiremold

For Holding The Conductors In Place. Finish - Galvanized Steel.

5400TB - Wiremold

Two Equal Compartments - Base Accepts Single or Twin Snap Cover. 5400 Series Raceway Is Available In 8' (2.4M) Lengths With Pre-Punched Mounting Holes, Packed 48' (14.6M) Per Carton. Ivory

5400TC - Wiremold

Use With 5400TB Series Raceway In Twin Snap Applications. Order Cover For Each Compartment. Available In 8' (2.44M) Lengths. Ivory

656 - Wiremold

For Removing Cover Of 1500 and 2600 Series Overfloor Raceways.

6ATC2PSB - Wiremold

Recessed Prewired Surface Style Poke-Thru Assembly – Designed to Be Installed In A Concrete Floor Which Has Access In The Ceiling Of The Floor Below For Running Power, Data and A/V Services. Poke-Thru Device Installs Into A 6" (152MM) to A 6 1/8" (155MM) Diameter Hole. The Unit Comes Complete With A Surface Style Cover and Two (2) Prewired, Pre-Installed Duplex Receptacles That Are Recessed 4" (102MM) Below The Floor Surface Level. Surface Style Cover Is An Aluminum Cover That Is Designed to Sit On Top Of

AL20GBA606TR - Wiremold

EFB45CTCBK - Wiremold

Evo 4 and 5 Gang Floor Box Surface Cover WTH Insert Black

G4017 - Wiremold

90 Degree Internal Corners. Fiber Bushing Included. Gray

RFB60G - Wiremold

For Use In Either Concrete or Wood Floors. Fully Adjustable With Tunnel Compartment. Supplied With Two (2) Duplex Mounting Plates, Two (2) Communication Mounting Plates (RFB62A), and (2) Blank Mounting Plates. Other Plates Sold Separately.